碳纳米管膜的高温纯化研究

为了获得纯度更高的碳纳米管膜, 保证材料发热稳定性, 需要对通过化学气相沉积法得到的碳纳米管膜进行二次纯化. 通过使用高温纯化炉, 在真空状态下, 从1700℃到3200℃分7挡温度对碳纳米管进行纯化, 并对其含碳量和方块电阻进行比较. 结果表明, 高温纯化后的碳纳米管膜含碳量从95.0%提高到99.9%, 解决了含碳量低的问题. 同时, 在高温纯化中发现碳纳米管膜方块电阻从纯化前3Ω降低到0.5Ω, 方块电阻的降低对碳纳米管膜具有十分重要的意义, 同样对碳纳米管膜后续产品的开发也有重要作用.     

A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.     

Precise Synthesis and Thin Film Self-Assembly of PLLA-b-PS Bottlebrush Block Copolymers

The ability of bottlebrush block copolymers (BBCPs) to self-assemble into ordered large periodic structures could greatly expand the scope of photonic and membrane technologies. In this paper, we describe a two-step synthesis of poly(l-lactide)-b-polystyrene (PLLA-b-PS) BBCPs and their rapid thin-film self-assembly. PLLA chains were grown from exo-5-norbornene-2-methanol via ring-opening polymerization (ROP) of l-lactide to produce norbornene-terminated PLLA. Norbonene-terminated PS was prepared using anionic polymerization followed by a termination reaction with exo-5-norbornene-2-carbonyl chloride. PLLA-b-PS BBCPs were prepared from these two norbornenyl macromonomers by a one-pot sequential ring opening metathesis polymerization (ROMP). PLLA-b-PS BBCPs thin-films exhibited cylindrical and lamellar morphologies depending on the relative block volume fractions, with domain sizes of 46–58 nm and periodicities of 70–102 nm. Additionally, nanoporous templates were produced by the selective etching of PLLA blocks from ordered structures. The findings described in this work provide further insight into the controlled synthesis of BBCPs leading to various possible morphologies for applications requiring large periodicities. Moreover, the rapid thin film patterning strategy demonstrated (>5 min) highlights the advantages of using PLLA-b-PS BBCP materials beyond their linear BCP analogues in terms of both dimensions achievable and reduced processing time.     

Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

基于DIS数字信息化系统对透光物质透光性能的研究

采用DIS数字信息化系统,对不同浓度的蓝墨水溶液在激光光源照射下的透射平均照度及照度分布图像进行实验研究,得到了平均照度值随溶液浓度变化的规律。对不同颜色塑料膜片对白炽灯光源透过照度值及照度分布图像进行实验研究得到及其相关之规律。     

Characterization of ZnO:AI films deposited by r.f.magnetron-sputtering at low temperature

Transparent conducting ZnO:AI thin films with good adhesion and Iow resistivity have been prepared on organic substrates and Coming 7059 glass substrates by r.f. magnetron-sputtering technique at Iow substrate temperature (25-210℃). Structural and photoelectric properties of the deposited films are investigated. The deposited films are polycrystalline with hexagonal structure and a preferred orientation with the c-axis perpendicular to the substrate. Only the (002) peak is observed.High quality films with resistivity as Iow as 1.0 x 10- 3Ω@ cm and 8.4 x 10- 4Ω@ cm, the average transmittance over 74% and 85% in the wavelength range of the visible spectrum have been obtained on different substrates.     

激光分子束外延方法生长的ZnO薄膜的发光特性

研究了不同温度和不同光激发强度下激光分子束外延方法生长的ZnO薄膜样品的发光性能,发现YAG脉冲激光激发,强度超过一定值时会在长波方向上出现一个新的发光峰,此峰可能起源于电子-空穴的复合。室温下氙灯激发的光谱中可以看到峰值位于381nm的近带边紫外发射峰和位于450nm的强的蓝绿带发射,根据光致发光激发光谱的特征给出了一个简单的蓝光发射模型。对比YAG脉冲激光激发和氙灯激发得到的实验光谱,我们认为不同的光谱特征和样品发光的激发机制有关,紫外峰发射需激发强度超过一定值才能观察到,而蓝带发射则在一定的激发强度下迅速饱和。     

Ⅱ-Ⅵ族化合物薄膜电致发光

电致发光薄膜是平板显示器的重要材料之一,我们从研究ZnS:Mn,Cu直流电致发光薄膜的大面积稳定发光开始,首次将稀土离子引进直流电致发光薄膜,实现了各色的直流电致发光,并研究其激发机理、过热电子的能量分布、稀土离子的碰撞截面和稀土离子发光中心在晶格中的位置等。在国内首先研制成功ZnS:Mn交流电致发光薄膜计算机终端显示器,并扩大面积到640×480像素(对角线10英寸)。为了实现彩色化显示,研制出稀土离子掺杂的各色交流电致发光薄膜。研究不同稀土离子在薄膜中的浓度猝灭,以便提高薄膜的发光亮度。在致力于实现彩色的过程中,首要的任务是提高蓝色电致发光薄膜的亮度和探索新的蓝色电致发光薄膜材料:从ZnS:TmF₃到CaS:TmF₃,发光亮度有了很大的提高;使SrS:Ce薄膜蓝色电致发光的亮度超过1000cd/m²;同时探索纳米Si和非晶Si/SiO₂超晶格结构的蓝色电致发光。成功地实现了ZnS:Mn/SrS:Ce白色电致发光和SrS:HoF₃三基色线谱发射的白色电致发光,发光亮度也超过1000cd/m²。     

富锌条件下生长氮掺杂氧化锌薄膜的光学和电学性质

报道了采用等离子体辅助分子束外延方法(P-MBE),利用NO作为N源和O源,在c-面蓝宝石(c-Al₂O₃)衬底上外延生长了N掺杂ZnO薄膜。X射线衍射谱(XRD)和吸收谱中都出现了不同于未掺杂样品的特性,X射线光电子谱(XPS)中也发现了N的受主信号。但是在霍尔效应(Hall-effect)测量中,发现该样品并没有出现预期的p型导电特性,而是出现载流子浓度很高(2.15×10²⁰cm^-3)的n型导电特性。结合XPS结果和理论分析,认为在富Zn条件下生长会导致过量的填隙Zn原子,补偿了全部的受主后,又促使其出现了从半导体-金属的Mott转变。     

ZnS作为空穴缓冲层的新型有机发光二极管

采用磁控溅射方法在ITO表面沉积了不同厚度的ZnS超薄膜作为有机发光二极管(OLEDs)的缓冲层,使典型结构(ITO/TPD/Alq3/Al)的OLEDs的发光性能得到改善。ZnS缓冲层厚度对器件性能影响的实验结果表明,当ZnS缓冲层厚度为5nm时,器件电流密度提高了近2倍,亮度提高了2倍;当ZnS缓冲层厚度为10nm时,器件发光的电流效率提高18%,器件的性能得到改善。宽禁带的ZnS缓冲层对空穴从阳极到有机功能层的注入有阻碍作用,促进器件载流子平衡,提高了器件发光效率,改善了器件性能。